IS230TCISH6C燃機模塊,GE中文PDF使用手冊
總結了187Bug調試器命令。這個命令語法使用中前面解釋的符號顯示本章。CNFG和ENV命令在中進行了解釋附錄A.控制器、設備及其LUN列在附錄B或附錄C。所有其他命令詳細信息包括MVME187Bug調試包用戶手冊中對此進行了解釋。本附錄涵蓋
? 配置電路板信息塊? 將環境設置為錯誤/操作系統
? 環境命令參數配置電路板信息塊CNFG[；[I][M]]
此命令用于顯示和配置電路板信息塊。該區塊位于非易失性
IS230TCISH6C燃機模塊RAM（NVRAM）。參考MVME187 RISC單板實際位置的計算機用戶手冊。
信息塊包含各種元素，詳細說明了特定的硬件的操作參數。MVME187 RISC單曲
Board Computer用戶手冊介紹了電路板信息塊，并列出每個電路板的大小和邏輯偏移量
要素CNFG命令不描述元素和它們的使用。對電路板信息塊內容進行校驗和用于驗證目的。該校驗和是塊請注意，引用的參數是左對齊字符（ASCII）字符串填充空格字符，引號（“）為顯示以指示字符串的大小。不適用的參數引用的被視為數據字符串，數據字符串是右對齊的。如果長度不為0，則用零填充數據字符串遇見。
如果董事會信息塊損壞，則命令顯示問號“”對于不可顯示字符。警告消息（警告：電路板信息塊校驗和錯誤）也會在校驗和失敗的情況下顯示。使用I選項初始化電路板的未使用區域信息塊歸零。允許使用命令的M選項進行修改。在修改會話結束時，系統會提示您輸入更新至非易失性RAM（NVRAM）。Y響應必須為進行更新；任何其他響應終止更新（忽略所有更改）。更新還重新計算校驗和。修改參數時要小心。這些參數是由工廠初始化，正確的電路板操作取決于這些參數。
The 187Bug debugger commands are summarized in Table 5-1. The
command syntax is shown using the symbols explained earlier in
this chapter. The CNFG and ENV commands are explained in
Appendix A. Controllers, devices, and their LUNs are listed in
Appendix B or Appendix C. All other command details are
explained in the MVME187Bug Debugging Package User's Manual.This Appendix Covers
? Configuring the board information block
? Setting the environment to Bug/Operating System
? Environment command parameters
Configuring the Board Information Block
CNFG [;[I][M]]
This command is used to display and configure the board
information block. This block is resident within the Non-Volatile
RAM (NVRAM). Refer to the MVME187 RISC Single Board
Computer User's Manual for the actual location.
The information block contains various elements detailing specific
operation parameters of the hardware. The MVME187 RISC Single
Board Computer User's Manual describes the elements within the
board information block, and lists the size and logical offset of each
element. The CNFG command does not describe the elements and
their use. The board information block contents are checksummed
for validation purposes. This checksum is the last element of the
block. Note that the parameters that are quoted are left-justified character
(ASCII) strings padded with space characters, and the quotes (") are
displayed to indicate the size of the string. Parameters that are not
quoted are considered data strings, and data strings are rightjustified. The data strings are padded with zeroes if the length is not
met.
In the event of corruption of the board information block, the
command displays a question mark "?" for nondisplayable
characters. A warning message (WARNING: Board Information Block
Checksum Error) is also displayed in the event of a checksum failure.
Using the I option initializes the unused area of the board
information block to zero.
Modification is permitted by using the M option of the command.
At the end of the modification session, you are prompted for the
update to Non-Volatile RAM (NVRAM). A Y response must be
made for the update to occur; any other response terminates the
update (disregards all changes). The update also recalculates the
checksum.
Be cautious when modifying parameters. These parameters are
initialized by the factory, and correct board operation relies upon
these parameters.
