GE T35繼電模塊,T35使用在哪里
100%到0%的周期重復校準周期數在<S9>中規定。記錄最終0%讀數后執行器在選定的沖程時間移動到位置來自MFP模塊的需求。當校準周期為完成后，執行器從如果IMHSS03模塊處于自動調諧狀態，則為MFP模塊模式在手動調諧模式下，當校準周期完成時，執行器傾斜到其預校準位置。讓循環完成。所有循環完成后校準的差分電壓寫入HSS模塊雙端口RAM。
GE T35繼電模塊觀察模塊狀態輸出塊N+6的位0和1。當LVDT校準為時，這些位的二進制值為0正在進行。校準完成后，這些位具有二進制值為1。如果模塊狀態位中出現二進制2，則錯誤在校準過程中發生。所有輸出都將顯示質量差，HSS模塊將保留以前的校準值。模塊狀態中的其他錯誤位輸出塊N+6和LVDT狀態輸出塊N+7將顯示發生的錯誤。參考第6節和表6-5用于糾正措施。更正錯誤后，重復校準程序。注：清除校準錯誤狀態和不良輸出質量
在不執行另一次校準的情況下，將校準模式設置為dis able，<S11>=0。
The 100% to 0% cycle repeats the number of calibration cycles
specified in <S9>. After recording the final 0% reading, the
actuator moves at the selected stroke time to the position
demand from the MFP module. When the calibration cycles are
complete, the actuator ramps to the position demand from the
MFP module if the IMHSS03 module is in the automatic tuning
mode. In manual tuning mode, the actuator ramps to its preca
libration position when the calibration cycles are complete.
Allow the cycle to complete. After completion of all cycles, the
calibrated differential voltages are written to HSS module
dual-port RAM.
6. Observe the module status output block N+6, bits 0 and 1.
The binary value of these bits is 0 while the LVDT calibration is
in progress. When the calibration is complete, these bits have a
binary value of 1.
If a binary 2 appears in the module status bits, then an error
has occurred during the calibration procedure. All outputs will
show bad quality and the HSS module will retain the previous
calibration values. The other error bits in the module status
output blocks N+6 and the LVDT status output blocks N+7 will
show which error has occurred. Refer to Section 6 and Table
6-5 for corrective action. After correcting the error, repeat the
calibration procedure.
NOTE: To clear the calibration error status and bad output qualities
without performing another calibration, set calibrate mode to dis
able, <S11> = 0.
